-
product
Mini Jumbo LCD Autoranging Multimeter
HH2202
High Accuracy (Basic Accuracy 1.0%). Jumbo LCD display 4000 count, 21mm figure height. Convenient Auto Ranging. Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 40MΩ. Diode test, audible continuity check
-
product
Ground Bond Tester
264
Our 264 Model makes Ground Bond / High Continuity Testing simple with 40 Amps of current to satisfy your NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 264 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
product
Multi-Network Cable Tester
3PK-NT007N
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
product
Digital (1kV below) Insulation Tester
2751 IN
Standard Electric Works Co., Ltd
● Timer for test function (count 3-5 minutes).● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm (2.677” × 1.338”) large LCD display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● External voltage warning indication.● Fuse protection.● Data hold function● Auto power off function.● BS 16 edition.
-
product
Multi-Modular Cable Tester
3PK-NT005N
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
product
Bench Digital Multimeter, Calibrated D & U, 1 kV, 10 A, 3.8 Digit
72-1015 CAL DU
The 72-1015 CAL DU from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro re...show more -
product
Process Calibrator
MC-1000
The MC-1000 Process Calibrator provides high accuracy calibration, common DMM functions including read and source thermocouples, RTDs, Ohms, current, pressure, frequency and test continuity. This single calibration instrument will calibrate virtually any process device including: read and source thermocouples, RTDs, Ohms, Voltage, Current, Frequency, Pressure, and test continuity.
-
product
Phase And Continuity Tester
4100
Peaceful Thriving Enterprise Co Ltd
There are two function of this tester. One is to test the continuity and the other one is to test the phase of three-phase system. The operation is easy, the indication is clear with LED indication. There is a loud buzzer to remind you the continuity. The illumination is very helpful in the dark environment.
-
product
Clamp On Meters
Triplett Test Equipment & Tools
1000A True RMS AC/DC clamp-on meter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Current, AC/DC Voltage, Resistance, Temperature, Capacitance, Continuity, Diode Test and NCV Detector. The rubberized overmolded housing provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. With a CAT III 600V design, it provides superior resistance to damage from transient overvolt...show more -
product
Automatic Wire Test Set
AWTS
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardw...show more -
product
Cable Tester
KT-45
Quickly test twisted cable RJ45 and BNC connector including T568A/B, 10-Base-T (UTP/STP), Token Ring, etc. Automatic test for open circuits, shorts, reversals, miswires, continuity. Main unit and one remote allow one person to test. Includes protective leather pouch. Testing before and after installation
-
product
Insulation & Multifunction Tester (LCD Display)
1153 AI
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Control and Switch Modules
Mini Mux
Eclypse International Mini Mux Control and Switch Modules, plus Software Developer Kit (SDK) provides high density test circuit switching as a complement to the Eclypse Circuit Analyzers. The Mini Mux Switching gives the user the ability to test continuity and isolation in complex assemblies with thousands of circuit paths (such as avionic back planes and chassis), while minimizing the test equipment complexity and footprint.
-
product
Ground Earth Resistance Tester
2678X
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
product
AC Clamp Meter
KT-3060
3 1/2 digits LCD,1999 counts ● Jaw size :Φ40mm ● Date hold● Black Light● Diode ,Continuity test● Resistance ,Frequency test
-
product
Breakout Box
T1000-9
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
product
HOTLink module (SAM)
ARINC 818
The HOTLinkTM stand alone module (SAM) is an invaluable tool for HOTLink testing. The SAM can be used as a portable signal converter, splitter, test pattern generator, or continuity tester. The SAM comes standard with an A/C adaptor and is also compatible with A/C 28 VDC.
-
product
3 1/2 digits (1999 count) Clamp Meter
KT-9030T
3 1/2 digits (1999 count), unit and sign display. ACA, ACV Measurement. Temperature Test. Continuity Beeper, Diode Test. Data-Hold function. Small size, light weight
-
product
Insulation & Multifunction Tester (LCD Display)
1152 MF
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
AC/DC Clamp Meter
3800 CL
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
product
Insulation & Multifunction Tester (LCD Display)
1151 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at Switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-null key.● Test Auto-stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Wristat Tester
WT 25-4145.26M
WT 25-4145.26M Wristat Tester is available to comply with D.O.D. 4145.26 specifications. The WT25-4145.26M Wristat Tester is designed to test the integrity of our WRISTAT in a fast, efficient, and simple manner. All the elements of the WRISTAT – continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact – are easily confirmed by pressing the top cover of the WT25-4145.26M. The operator (wearer) is tested for a resistance to ground of greater than 250K o...show more -
product
Volt Tester
PPTACT1CS
THE PROBE 12-Volt Test Light with Haptic Feedback, (PPTACT1CS) this tool vibrates and lights when voltage over 12 volts is detected. When a voltage is below 12 volts, this functions as a standard test light. Just push the button and go! Shows positive voltage, ground, and continuity “all in one tool” with haptic advantage.
-
product
Multifunction Tester
COMBI521
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
Require External Wireless Module
Insulation Tester
*Tests insulation upto 4Gohm with 4 different voltage range : 125V ; 250V ; 500V ; 1000V ( > 1mA )*Pre-set timer settable*Good / NG comparison*Auto high voltage detection*AC voltage test upto 1000V*DC voltage test upto 750V*Resistance test*Continuity check ( > 200 mA )*NCD’ Non-Contact AC Voltage Detection with patented numerical display AC signal strength ( > 50V AC )
-
product
AstroAI Digital Multimeter
TRMS 4000
WIDE RANGE of tests for AC/DC Voltage, AC/DC Current, Resistance, Continuity, Capacitance, Frequency and Temperature; Tests DiodesPROFESSIONAL LEVEL features include Auto-Ranging capability, and True RMS for measuring both AC Current and Voltage
-
product
Loudspeaker Cable Testers
EMO E450
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
product
Analyzer for Safety Agency Production Line Testing
HypotULTRAIII
Ethernet Communication CardUSB/RS-232, GPIB & Printer InterfacesData Storage CardInterconnection to Modular Scanning MatrixOptional 10 Volt Analog InterfaceStorage of up to 50 setups with 30 steps per setupPatented SmartGFI® functionPatented prompt and hold functionPatented CAL-ALERT® functionPatented VERI-CHEK® functionReal Current measurementDual Continuity test modesBuilt-in security settingsLine and Load regulation
-
product
Cable Tester
KT-468
Test device used UTP and STP network wiring and phone line. Check continuity and configuration of wiring with unshielded and shielded modular plugs. Test for open circuits,shorts,miswires and reversals. SHIELD detection tests a cable`s shield integrity. Main unit and one remote allow one person testing
-
product
Insulation & Multifunction Tester (LCD Display)
4153 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Insulation Resistance, voltage (AC-DC) measurements with automatic hold facility, diode, ohm, and continuity with a short circuit current of minimum 220mA.● Auto-off function.● Energy conservation feature.● Ener-Save™ limit the test duration to about 10 Seconds.● Quick Test and EnerSave™ are unique features. Both saves energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Operates with rechargeable batteries, alkaline or low cost general purpose batteries.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
